Technical Support Archives - Page 10 of 15 - DDM Garage Doors Blog

Torsion Spring Winding Systems

Friday, July 21st, 2017 at 1:52 pm by Sales Team

Winding residential torsion springs is dangerous. If you are not careful, and if you do not have the proper tools, it is easy to get hurt. To make the process safer for DIYers, a number of garage door manufacturers developed their own torsion spring winding systems.…

Read the rest of this entry »

Garage Door Noise

Friday, July 7th, 2017 at 3:41 pm by Sales Team

Ultimately, every garage door opener will make noise. It’s impossible to get something as large and as heavy as a garage door to be whisper quiet. In earlier decades, it didn’t matter because many garages were detached, but in the last 20-25 years, most single-family homes have been built with attached garages.…

Read the rest of this entry »

High Lift Kit FAQs

Friday, June 16th, 2017 at 1:27 pm by Sales Team
A GIF of a high lift track conversion.
An image indicating the high lift measurement in red with a question mark.

1: How much does a high lift kit cost?

A custom high lift from DDM typically costs $350 – $500. This does not include an operator; with an operator the cost is $900 – $1100. In addition to the kit cost, expect shipping costs of $50 – $150.…

Read the rest of this entry »

Push Down Bumper Springs and Leaf Bumpers

Friday, June 2nd, 2017 at 11:48 am by Sales Team

Push Down Bumper Springs start the door on the down cycle by pushing on the top of the door.

Jackshaft openers such as the Liftmaster 8500 or the 8500W turn the torsion shaft to operate the door. Under certain circumstances, it is advisable to use pusher springs to help the door close if the door cables come off the drums as the door begins to close.…

Read the rest of this entry »

Clopay Pinch Proof – The Downside to Unique Hardware

Friday, May 26th, 2017 at 1:00 pm by Sales Team

We’re sorry, but the pinch-proof hinges are no longer available.

As you see below, they were available for a while in 2018, but they are no longer available.

Yesterday I was at the Clopay Chicagoland distribution center, picking up a shipment of Clopay EZ-SET Springs.…

Read the rest of this entry »

Solid or Hollow Stop Molding?

Friday, May 19th, 2017 at 1:00 pm by Sales Team

The garage door industry uses two different types of PVC stop molding – solid and hollow. So which one is better?

A comparison between a two-inch hollow white and two-inch solid white stop moldings.

At DDM Garage Doors, we have kept both the solid and the hollow stop molding pieces as stock items for as long as we’ve been in business.…

Read the rest of this entry »

Solutions for Cable Problems on Doors with Jackshaft Operators

Tuesday, June 21st, 2016 at 11:37 am by Dan Musick

There are two types of operators, drawbar with trolley and jackshaft. We will cover some potential solutions since Jackshaft operators tend to cause cable problems.

On trolley type operators, the drawbar arm pushes and pulls the top of the door to open and close it.…

Read the rest of this entry »

Converting from Two to Four Torsion Springs

Saturday, May 28th, 2016 at 2:38 pm by Dan Musick

When upgrading to longer life torsion springs, it is often better to convert to four smaller springs. This is especially true when the torsion springs are for heavier garage doors.

On a standard two spring system, both torsion springs normally mount back to back to the spring anchor bracket off-centered above the door.…

Read the rest of this entry »

Overhead Door vs. Arrow Tru-Line Hinges

Monday, May 9th, 2016 at 4:14 pm by Dan Musick

Overhead Door Corporation has discontinued the production of its own brand of hinges.

The Arrow Tru-Line hinges are an excellent replacement. However, the holes don’t always line up with the existing carriage bolts on the older wooden doors.

An image of an Overhead Door hing on the left side, next to an Arrow Tru-Line hinge on the right.

You can see the difference between the Overhead Door and Arrow Tru-Line hinges in the image below.…

Read the rest of this entry »

The EZ-Set Bearing Keeps Coming Out

Friday, May 6th, 2016 at 4:29 pm by Dan Musick

We received an email this week from a do-it-yourselfer who had installed a Clopay door with an EZ-SET torsion spring set up. On his door, he has a single spring with a winder at the left end of the torsion assembly.…

Read the rest of this entry »

Since 1997 the Gold Standard for Online Garage Door Parts

CUSTOMER SUPPORT HELP WANTED

Huge inventory of torsion springs for same or next day shipping! Here you will find all you need in the most common sizes of 1 3/4," 2," 2 1/4," and 2 5/8" inside diameter springs. Larger 3 3/4" and 6" inside diameter commercial and industrial springs may require a day or two to ship. You'll also find TorqueMaster Springs, Extension Springs, Self-Storage door springs, steel rolling door springs and springs for one piece single panel doors.

Shelves packed with every part you need to fix your doors.

Please note. Shipping times and costs have changed. Normal transit times are currently not guaranteed, even on next day and second day shipments. Shipping prices on items over eight feet have more than tripled.