Technical Support Archives - Page 13 of 15 - DDM Garage Doors Blog

Wayne Dalton Torquemaster Springs: Solving the Puzzle

Thursday, February 26th, 2015 at 4:00 pm by Dan Musick

It seems that Wayne Dalton TorqueMaster springs fly off the shelves at our office here at DDM. Amid all the flurry of taking orders, processing, wrapping, and shipping the springs, some common misconceptions regarding the springs arise.

Although Wayne Dalton makes many models and sizes of doors, they do not make TorqueMaster springs based on these doors.…

Read the rest of this entry »

How To Replace Garage Door Torsion Springs – Safely and Correctly

Sunday, September 9th, 2012 at 3:57 pm by Dan Musick

The video is here live! All the steps for how to replace garage door torsion springs on a two-spring system are given in clear, sequential steps. Therefore, decide whether this is something you would like to try as a DIY project.…

Read the rest of this entry »

Installing Garage Door Springs – Safely and Right the First Time, Part 1

Thursday, March 22nd, 2012 at 1:13 pm by Dan Musick
An image of a standard bearing and a nylon bushing used when installing garage door springs.

So you’ve seen our page on installing garage door torsion springs …

In the process of digesting all the information, customers sometimes make a dangerous assumption.

When installing two garage door springs, using two bushings or bearings sounds reasonable – it seems to make sense.…

Read the rest of this entry »

Garage Door Springs Sold On Merchant Sites Not All That Good

Thursday, December 8th, 2011 at 10:20 am by Dan Musick

Oh, the buzz that happens on the Web about garage door springs

Extreme ranges of opinion and practice lurk everywhere. Some people say it’s illegal to sell them. Others advertise them to be as standard and common as pliers or wrenches.…

Read the rest of this entry »

When You Buy Garage Door Springs – Think Batting Averages

Wednesday, November 23rd, 2011 at 3:59 pm by Dan Musick
An image of a baseball bat handle with batting averages surrounding it comparing them to garage door spring wire sizes.

If you buy garage door torsion springs – even in the off season – remember batting averages.

Measure garage door springs using a tape measure, 10-and 20-coil counts. Use the conversion chart at the measurement link.

Express the wire size in terms of a three-digit decimal – .262, for example.…

Read the rest of this entry »

Buy Garage Door Weatherstripping – And Avoid these Seven Common Errors

Friday, November 4th, 2011 at 9:16 am by Dan Musick

When you buy garage door weatherstripping this winter season, beware of these common error issues en route to your purchase:

1. Not buying enough weatherstripping for your door’s height or width.

It is best to over-order a little than to undershoot.…

Read the rest of this entry »

Vertical Lift a Good Alternative to High Lift Garage Door?

Thursday, October 13th, 2011 at 9:27 am by Dan Musick

High lift or vertical lift? The answer is up to you.

A view of a vertical lift garage door.

I receive numerous calls every week from customers who want to raise the lift of their garage doors. Here are some considerations:

You may want a vertical lift system if your garage has at least the door’s height plus 18″ of room above your door’s original height AND…

a.…

Read the rest of this entry »

Fast Track Facts For Fall

Thursday, October 6th, 2011 at 2:14 pm by Dan Musick

Remember, 2″ vertical track for 7′ high doors measures 6’4″, or 76″. If you measure a track radius, this is the point where the level goes.

An image of a vertical track for 7 foot high doors.

You need to order only one 7′ track if one is damaged. In addition, 7′ vertical track is adaptable for your left or right side, as you are standing inside the garage.…

Read the rest of this entry »

Clopay EZ-Set Springs – How to Remove the Spring Winding Cone From the Winder

Thursday, August 11th, 2011 at 4:02 pm by Dan Musick

Customers ordering Clopay EZ-SET springs from DDM should be very careful when removing the old spring from the winder.

Below are sequenced pictures of how coins can be used to get the cone off the winder without damaging the plastic clips that hold the cone in place:

A view of Clopay EZ-Set Cone and winder.

Left: Clopay EZ-SET winder with cone

Below: Loosen one side of the cone by carefully inserting a screwdriver and lifting

An image of cone being loosened by a screwdriver.

Next, insert two coins under the cone near the point it was loosened

A view of coins placed under an EZ-SET cone.

Then, turn the winder clockwise until the other release point on the cone is accessible

A person turning a winder on a Torsion Spring Winder.

Finally, carefully use a screwdriver to loosen the other release point, now visible

An image of screwdriver placed under a cone to loosen it.

Believe me; you’ll save a lot more than the two pennies by being careful with this!…

Read the rest of this entry »

Need Winding Bars For Your Garage Door Torsion Spring Replacement?

Thursday, June 30th, 2011 at 3:37 pm by Dan Musick

Do you need to buy garage door torsion springs? Winding bars for your garage door are an often-overlooked part of a torsion spring replacement job, but they are vital. Ratchet handles, tire irons, jack handles, or other tools cannot safely and effectively take their place.…

Read the rest of this entry »

Since 1997 the Gold Standard for Online Garage Door Parts

CUSTOMER SUPPORT HELP WANTED

Huge inventory of torsion springs for same or next day shipping! Here you will find all you need in the most common sizes of 1 3/4," 2," 2 1/4," and 2 5/8" inside diameter springs. Larger 3 3/4" and 6" inside diameter commercial and industrial springs may require a day or two to ship. You'll also find TorqueMaster Springs, Extension Springs, Self-Storage door springs, steel rolling door springs and springs for one piece single panel doors.

Shelves packed with every part you need to fix your doors.

Please note. Shipping times and costs have changed. Normal transit times are currently not guaranteed, even on next day and second day shipments. Shipping prices on items over eight feet have more than tripled.